Antique Allis Chalmers Tractor Parts

                                 
                     
   
                               
Steering Joint Repair Kits

Steering Universal Joints Repair Kit

Fits Allis Chalmers RC, WC, WD, WD45 & WD45D Replaces # 202152 (Shaft diameters 7/8 inch and 1 inch, U-Joint Caps diameter .750 inch)
ABC167
 $67.70

Steering Universal Joints Repair Kit

Fits Allis Chalmers Late WC, WD, WD45, WD45 diesel, Replaces #224825 (Shaft diameters 7/8 inch and 1 inch, U-Joint Caps diameter .936 inch, HD-Heavy Duty, For loader use)
 
ABC280
 $99.25
   

Steering Universal Joints Repair Kit

Fits Allis Chalmers D17 & D19, Replaces #228906 (SHAFT DIAMETER 13/16 inch AND 3/4 inch keyed)
 
See above
   
 
ABC274
 $153.45            
                           
 

Steering Shaft Tube Without Bushing

Fits Allis Chalmers: G. Primed --- 50-1/2" Long X 1 1/2" OD --- Does not include bushing. Replaces: 800097
ACS337
 $64.95            
 

Upper Steering Shaft Tube Bushing

Fits Allis Chalmers: Following with Ross Steering Box: B, C, CA, IB & G. To fit original tube must sand approximately .005 off OD of bushing --- 1-3/8" OD --- 3/4" ID. Replaces: 210475.
ACS339
 $19.95
 

Steering Shaft Tube Without Bushing

Fits Allis Chalmers: Following with Ross Steering Box: B. Primer --- 40-15/16" Long --- 1 1/2" OD --- Does not include bushing: Replaces: 210472 & 206765.

ACS341
 $74.95
 

Steering Shaft Tube Without Bushing

Fits Allis Chalmers: Following with Ross Steering Box: C. PRIMER --- 40" Overall X 1 1/2" OD --- Does not include bushing. Replaces: 219390.

ACS343
 $74.95
 

Steering Tube Mounting Brackets (Pair)

Fits Allis Chalmers: B, C, CA, IB & G. Primer. Replaces: 207218.

ACS345
 $29.95
 
Char-Lynn Power Steering Parts  
   

Slip Fit or Economy Coupler
(For Power Steering Conversion)

Fits Allis Chalmers models when equipped with Char Lynn Add-On Power Steering
ABC380
 $137.00
Original
ABC497
 $29.40
Economy
           

Torque Generator
(Standard)

For when pulling a wagon, etc... (Torque Output at 1000 PSI = 7000 inch lbs., Rated Operating Pressure = 1000 PSI, Maximum Operating Speed at 3 GPM = 108 RPM, Recommended Fluid Input = 2.5 to 3 GPM)
 
IHS554
 $438.20
       

Torque Generator
(Heavy Duty)

For when a front loader is used (Torque Output at 1000 PSI = 1100 inch lbs., Rated Operating Pressure = 1000 PSI, Maximum Operating Speed at 3 GPM = 65 RPM, Recommended Fluid Input = 3 to 4 GPM)
   
See above
 
       
IHS555
 $449.50

Port Block

Needed only if above Torque Generators are purchased
   
IHS673
 $81.25

Power Steering Priority Flow Control Valve

Fits Allis Chalmers WC, WD, WD45, WD45D -- ALL WITH LIVE HYDRAULICS
NOTE: ELIMINATES BELT DRIVEN PUMP, PULLEYS & BRACKETS. ENABLES YOU TO USE YOUR LIVE HYDRAULIC PUMP TO OPERATE THE POWER STEERING. --- MUST BE USED W/ LIVE HYD. --- 3/4" INLET & RETURN --- 1/2" PRESSURE PORT -- PRE SET AT 1500 PSI, ADJUST TO YOUR APPLICATION
 
IHS740
 $198.95            
                         
Power Steering Cap                
                   

Power Steering Cap

Fits Allis Chalmers WD45 GAS & DIESEL
                       
IHS338
 $8.50    
 
Tie Rod, Parts  
 

RH & LH Tie Rod End

Fits Allis Chalmers B & C, Replaces #207725

ACS211
 $46.95      
RH
ACS213
LH
$46.95  
 

Tie Rod ( 2 Piece)

Fits Allis Chalmers D14, D15, D17, D19, 170, 175, 180, 185, 190, 190XT, 200, --- WD, WD45, Replaces 254661 & AC:254662, 225279, 225280, 249418 --- CAN REPLACE AC:250142 & 250141 IF CUT TO LENGTH, 19 ¼ Closed, 29 ¾ lengthened
NOTE: USED ON WD & WD45 IF CUT TO LENGTH. --- USED ON C & CA WITH ADJUSTABLE WIDE FRONT AXLE

 
ACS066
 $59.95            
                         

Rear Axle

Fits Allis Chalmers G, Replaces #800902 (24 3/8 inches overall length)

TEMPORARY Unavailable
 
ACS006
 $194.95      
 
     
 
 
 
Page 1 2