Antique International Tractor Parts

Inner Threaded Tie Rod

Fits LATE SUPER A SN 318310 & UP, SUPER AV SN 318310 & UP, C, SUPER C, 100, 130, 200, 230, 385, 2424, 424, SOME 454, 485, 464 W/ SWEPT BACK AXLE. Replaces 356540R91
NOTE: FITS MODELS LISTED WITH AUTOMOTIVE TYPE TIE ROD ENDS. 3.062" END TO GREASE ZERK. 11/16 X 16 RH THREAD

Outer Tie Rod End (notched)

Fits LATE SUPER A SN 318310 & UP, SUPER AV SN 318310 & UP, C, SUPER C, 100, 130, 200, 230, 385, SOME 454, 485, 574, 585, 595, 674, 784, 884, 885, 495, 695 SWEPT BACK, 464, 484 SWEPT BACK WITH 44-72" AXLE OR 48-80" AXLE, Replaces 65077C91, 360412R11, FITS MODELS LISTED WITH AUTOMOTIVE TYPE TIE ROD ENDS
NOTE: 2 DIFFERENT ONES - CHECK DIMENSIONS BEFORE ORDERING. --- 16" END TO GREASE ZERK --- 0.750 DIA ROD

Threaded Inner OR Outer Tie Rod End

Fits H, SUPER H, M, MD, SUPER M, SUPER MD, SUPER MTA, 300 ROWCROP, 350 ROWCROP, 400, 450, 460, 544, 560, 656, 666, 686, 706, 756, 766, 786, 806, 826, 856, 886, 966, 986, 1026, 1066, 1086, 1206, 1256, 1456, 1466, 1468, 1486, 1566, 1568, 1586, HYDRO 70, HYDRO 100, HYDRO 186, Replaces 384006R92
NOTE: 1" THREADED R/H, 16 THREAD, 3.750 FROM THREADED END TO GREASE ZERK

Mounting Bracket

Fits M, Super M & MTA

Power Steering Resevoir Cap (Gas Cap)

Fits M, SUPER M, MTA, MV, MDV, SUPER MV, SUPER MDV, MADE IN USA. IMPROVED QUALITY. DIP STICK IS NOT INCLUDED --- THIS CAP IS USED / CAN BE USED FOR THE FOLLOWING PURPOSES ON VARIOUS MODELS: --- AUXILIARY TANK GAS CAP --- POWER STEERING RESERVOIR CAP --- OIL FILLER CAP --- ENGINE OIL CAP

Slip Fit or Economy Coupler
(For Power Steering Conversion)

Fits International models when equipped with Char Lynn Add-On Power Steering

Torque Generator
(Standard)

Fits M, Super M, MTA, 400 & 450 for when pulling a wagon, etc... (Torque Output at 1000 PSI = 7000 inch lbs., Rated Operating Pressure = 1000 PSI, Maximum Operating Speed at 3 GPM = 108 RPM, Recommended Fluid Input = 2.5 to 3 GPM)

Torque Generator
(Heavy Duty)

Fits M, Super M, MTA, 400 & 450 for when a front loader is used (Torque Output at 1000 PSI = 1100 inch lbs., Rated Operating Pressure = 1000 PSI, Maximum Operating Speed at 3 GPM = 65 RPM, Recommended Fluid Input = 3 to 4 GPM)

Port Block

Needed only if above Torque Generators are purchased

Power Steering Priority Flow Control Valve

Fits H, SUPER H, HV, SUPER HV, M, SUPER M, MD, MTA, MV, MDV, SUPER MV, SUPER MDV, W4, W6, W9, WD6, SUPER W6, SUPER W4, SUPER W6, SUPER W9, WR9, WD9, SUPER W6TA, SUPER W6TA DSL, SUPER WDR9, 300, 350, 400, 450, ELIMINATES BELT DRIVEN PUMP, PULLEYS & BRACKETS. ENABLES YOU TO USE YOUR LIVE HYDRAULIC PUMP TO OPERATE THE POWER STEERING. --- MUST BE USED W/ LIVE HYD. --- 3/4" INLET & RETURN --- 1/2" PRESSURE PORT -- PRE SET AT 1500 PSI, ADJUST TO YOUR APPLICATION

Front Wheel Seal

Fits H, Super H, M, Super M, MD, MTA, Super MD, 4, Super W4, 300 & 350, 400, 450, W400 & W450 Replaces IH #48702D

Wheel Clamp Lock Nut
(For Axle Shaft and Front Wheel)

Fits A, B, BN, C, 100, 130, 200, 240, 330 & 340 (5/8 inch - 18 thread) No re-threading necessary on worn shafts!