Hitch and Hydraulics
JDS4539 End, Rockshaft Lift Control Cable
|
JDS5741 Hydraulic Pump 50CC
|
MHSK1 Deck Stabilizer Kit
|
ABC209 Block & Hydraulic Drain Plug - 1/4" - 18 NPT
|
JDS225 Implement Hex Nut 1 1/4" (TALL) X 1 1/16" (WIDE) X 5/8"-11 NC --- MOUNTS TO FRONT AND REAR OF AXLE HOUSINGS
|
JDS4689 Hydraulic Pump 50CC
|
JDS4673 Hydraulic Pump 40CC
|
JDS500 Oil Fill Breather Cap on Allis and Hydraulic Fill Cap on John Deere's - 1.5" Tall --- includes clip, fits over a 1.5" pipe
|
|
|
AR94660 Pump, Hydraulic Assembly - Fits JD 3010, 3020, 4000, 4010, 4020, 4040, 4050, 4055, 4230, 4240, 4250, 4255, 4320, 4350, 4430, 4440, 4450, 4455, 4520, 4620, 4630, 4640, 4840, 5010, 5020, 6030, - 50 cm, 1 1/16" Discharge Port, 1 1/16" Inlet Ports
|
JDS3861 Front Hydraulic Pump Drive Clamp Half - 5.142" overall length 2" wide (1) 3/8"-16 NC threaded hole
|
JDS3510 Hydraulic Power-Trol or Breakaway Coupler O-Ring Kit - Includes 6 O-rings: (2) outer O-rings and (4) inner O-rings.
|
JDS427CVR Cover - Ford Swinging style lever Power-Trol
|
JDS427S Coupler Only (No Cover) - Swinging style lever Power-Trol, 1/2" pipe thread - USA Made
|
JDS427 Hydraulic Coupler With Cover - Swinging style lever Power-Trol, 1/2" pipe thread
|
JDS772 Hydraulic Block Off Plug - Swinging style lever Power-Trol, 1/2" pipe thread
|
ABC2010 Category 1 Adjustable Stabilizer Bar - Adjustable ends for desired length, adjust from 27-1/2" to 37" length. 23" center tube length. 7/8" threaded ends. 7/8" pin holes
|
FDS023 Top Link - Category 1, 16" long tube, 3/4" holes at both ends
|
FDS022 3 Point Drawbar - Category 1, black primer, measures 1" x 2-1/2" x 26", (approximately 31-1/2" overall length, pin to pin) with a 7/8" pin size
|
JDS078A Top Link Hook End - 1-1/4" thread
|
MIS4560 Hitch Pin 7/8" x 6-1/2"
|
MIS4555 Hitch Pin 3/4" x 6-1/2"
|
MIS4563 Hitch Pin 1" x 7-1/2"
|
ABC532 Toplink Ball Category 2 - 1.988" outside (nominal) diameter 1.015" hole diameter 1.374" diameter of flat 2.008" width 48 - 55 Rockwell 4142 steel zinc plated
|
ABC1433 Lift Arm / Top Link Reducer Bushing - For tractors with Category 2 3 PT hitch switching to category 1 3PT. ***7/8" ID --- 1-1/8" OD --- 1-3/8" overall Length***
|
ABC4185 Top Link Reducer Bushing, Category 2 to Category 1 - 0.750" I.D., 1.000" O.D., 1-15/16" length
|
ABC530 Toplink Ball Category 1 - 1.988" outside (nominal) diameter, 0.765" hole diameter, 1.310" diameter of flat, 1.720" width, steel zinc plated
|
FDS211 Drawbar Lock - Category 1
|
JDS547 3 Point Lift Link Assembly - Adjustable; 17-3/4" Minimum to 24-1/2" maximum length
|
|
|